CELL SELECTION MATRIX
软包 / 方形 / 圆柱 / 刀片 × 磷酸铁锂 / 三元 / 钛酸锂 / 钠离子 / 半固态 —— 18 组可得组合的能量密度、循环寿命、低温、倍率、工艺风险与出口管制注意项,一次讲清。Pouch / prismatic / cylindrical / blade × LiFePO₄ / NCM / LTO / Na-ion / hybrid solid-liquid — eighteen obtainable combinations compared on energy density, cycle life, cold performance, C-rate, process risk and export-control exposure.
数据口径 2026 年 11 月 · 区间参考值;正式方案以选定型号规格书与第三方检测报告为准Data as of November 2026 · indicative ranges; final design follows the selected cell datasheet and third-party test reports.
CHINA MANDATORY STANDARDS
我们主要服务中国内陆客户。选型之前先确认标准适用性:2025—2027 年国内锂电强制标准密集收口,多数客户的第一个问题已经不是「多少钱」,而是「过没过」。We serve mainland Chinese customers. Confirm standard applicability before selecting cells: China's mandatory lithium-battery standards tightened sharply across 2025–2027, so the first question is often "has it passed", not "how much".
我国储能锂电池首部强制性国标,2024-07-24 发布、2025-08-01 起实施。电芯层新增振动、加速冲击、浅刺、强制放电;过充加严为充至 1.5 倍限制电压后恒压 1 小时;系统级要求热失控后不蔓延、无明火。招标已普遍把它写成硬门槛。China's first mandatory storage-battery safety standard, published 24 Jul 2024, effective 1 Aug 2025. Adds vibration, acceleration-shock, shallow-needle and forced-discharge tests at cell level; overcharge tightened to 1.5× the limit voltage held 1 h; system level requires no propagation and no flame after thermal runaway. Tenders now treat it as a hard gate.
GB 47372-2026 于 2026-03-31 发布,认监委 2026 年第 7 号公告将其纳入 CCC 依据,分 0914(充电宝、便携式储能:GB 4943.1 + GB 31241 + GB 47372)、0915(便携电子产品用锂电:仅 GB 31241)、0916(移动电源专用锂电:GB 31241 + GB 47372)。过渡期至 2027-03-31,2027-04-01 起全面执行新规则,旧证书须完成转换;新增漏液强制抽检与针刺要求。Published 31 Mar 2026 and added to CCC by CNCA Announcement No. 7 of 2026, split into 0914 (power banks and portable stations: GB 4943.1 + GB 31241 + GB 47372), 0915 (portable-device cells: GB 31241 only) and 0916 (cells for mobile power: GB 31241 + GB 47372). Transition to 31 Mar 2027; the new rules apply fully from 1 Apr 2027 and old certificates must be converted. Leaktightness sampling and nail tests are new.
GB 43854-2024 自 2024-11-01 实施(单体含针刺等 6 项 + 电池组 22 项);GB 17761-2024 自 2025-09-01 生产端实施;CNCA-C11-16:2026 自 2026-11-01 起所有新认证申请按新规,整车 / 电池 / 充电器各自赋唯一溯源码并充放电互认协同。电池不认控制器就放不出电——这对 BMS 通信能力是硬要求。GB 43854-2024 applies since 1 Nov 2024 (six cell tests including nail, 22 pack tests); GB 17761-2024 from 1 Sep 2025; CNCA-C11-16:2026 governs all new applications from 1 Nov 2026, giving vehicle, battery and charger each a unique traceability code with charge and discharge mutual authentication — a cell that cannot hand-shake with the controller cannot discharge, which is a hard requirement on BMS communication.
GB 38031-2025 自 2026-07-01 实施:热失控后观察期内不起火不爆炸(由「报警 5 分钟」升级为「2 小时不起火不爆炸」)、新增底部撞击(30mm 撞头 150J 连续 3 次)与快充循环 300 次后短路测试;GB 18384-2025 要求高压回路物理「一键断电」。命名侧按 GB/T 43568-2026:电解液质量占比 5%–20% 为「混合固液电池」,低于 5% 且通过 120℃ 真空 6h、失重率 ≤0.5% 才可称「全固态」。GB 38031-2025 (effective 1 Jul 2026) requires no fire or explosion during the observation window after thermal runaway — upgraded from a 5-minute alarm to 2 hours without fire — plus a new bottom-impact test (30 mm head, 150 J, three hits) and short-circuit after 300 fast-charge cycles; GB 18384-2025 mandates a physical high-voltage disconnect. Naming follows GB/T 43568-2026: 5–20% electrolyte by mass is a hybrid solid-liquid cell; only below 5%, passing 120 ℃ vacuum for 6 h at ≤0.5% weight loss, may be called all-solid-state.
自 2025-06-28 起,无 CCC 标志、标志不清晰或被召回型号批次的充电宝,禁止旅客携带乘坐境内航班(火车无强制 CCC,但要求标识清晰且额定能量 ≤100Wh)。做便携储能产品线时,这是可以直接写进卖点的合规事实。Since 28 Jun 2025, power banks without a legible CCC mark, or of recalled models or batches, may not be carried onto domestic flights (rail has no CCC requirement but needs clear markings and ≤100 Wh). For portable-power lines this is a compliance fact worth selling.
HOW TO USE
「形态」回答结构与工艺问题,「化学体系」回答能量与寿命问题。任何体系都可以做成任一种形态(市场可得性另说),所以选型是这两轴的交叉,而不是二选一。Format answers structural and process questions; chemistry answers energy and life questions. Any chemistry can be built in any format (availability aside), so selection is a crossing of two axes — not a choice between them.
重量?体积?成本?寿命?温度?认证?先确定客户唯一不能让步的那一项。Weight, volume, cost, life, temperature or certification — name the one thing that cannot move.
用「形态横向」决定软包 / 方形 / 圆柱 / 刀片,同时确定 PACK 工艺与增项成本。Use the format table to choose pouch / prismatic / cylindrical / blade — which also sets PACK process and add-on cost.
用「五体系速览」把范围收到 1–2 个体系。Use the five-chemistry overview to narrow to one or two systems.
对到「应用场景」与「出口管制」两节,确认交期与合规可落地。Match against the scenario and export-control sections to confirm lead time and compliance.
整包要计入 BMS、结构件、线束、箱体与热管理重量,成组效率通常为电芯级的 70%–85%(软包 0.86–0.88、方形 0.83–0.85、圆柱 0.75–0.80)。客户报「400Wh/kg」时,先确认是电芯级还是整包级、是质量还是体积能量密度。A PACK carries BMS, structure, harness, enclosure and thermal mass; utilisation is typically 70–85% of the cell (pouch 0.86–0.88, prismatic 0.83–0.85, cylindrical 0.75–0.80). When a customer quotes "400 Wh/kg", confirm cell- vs pack-level and gravimetric vs volumetric.
STEP 1 · FORMAT
一句话记忆:软包赢在能量密度与尺寸灵活,方形赢在成本、安全冗余与交付速度,圆柱赢在现货、倍率与防爆适配,刀片赢在体积利用率与结构集成。In short: pouch wins energy density and dimensional freedom, prismatic wins cost, safety margin and delivery speed, cylindrical wins availability, C-rate and explosion-proof compatibility, blade wins volumetric utilisation and structural integration.
| 对比维度Dimension | 软包 PouchPouch | 方形 PrismaticPrismatic | 圆柱 CylindricalCylindrical | 刀片 BladeBlade |
|---|---|---|---|---|
| 结构本体Construction | 铝塑膜封装,极耳外露,无边框支撑Aluminium-laminate film, exposed tabs, no structural frame | 铝壳或钢壳 + 顶盖(防爆阀、CID、注液孔)Aluminium or steel can + top cap (vent, CID, fill port) | 镀镍钢壳卷绕,顶盖带安全阀与 CID,单体小Nickel-plated steel can, wound, vent + CID, small cell | 长薄金属壳(铝 / 钢),两端极柱,长度可超 1m,可兼作结构梁Long, thin metal can (Al/steel), terminals at both ends, over 1 m long — can double as a structural beam |
| 单体能量密度Cell energy density | 最高,比同体系方形高 10–20%Highest, 10–20% above prismatic in the same system | 中等,壳体占比大Mid — heavy can share | 中高(高镍 21700 可达 300Wh/kg),但成组后拉低Med-high (300 Wh/kg Ni-rich 21700) but diluted at pack level | 160–200,铁锂刀片常见 160–190160–200; LFP blade typically 160–190 |
| 成组效率Utilisation | 0.86–0.88 | 0.83–0.85 | 0.75–0.80 | 0.85–0.90 |
| 机械约束要求Mechanical constraint | 必须整体侧向压紧并预留膨胀(循环厚度增 2–3mm),结构最敏感Full side clamping plus swell allowance (2–3 mm thickness growth) — most structure-sensitive | 仅需端板压紧,力矩有明确规格,工程最省事End-plate compression only, defined torque spec — easiest to engineer | 靠塑料支架固定,几乎无压紧要求,但要留散热间隙Held by plastic holders, minimal preload, but needs thermal gaps | 沿厚度方向压紧并固定端部;电芯自身承力,箱体可简化,但平面度要求高Thickness-direction preload plus end fixing; cells carry load, simplifying the enclosure but demanding flatness |
| 散热与热扩散Cooling & propagation | 叠层方向导热差,需大面积导热垫,单体间必须加隔热片Poor through-stack conduction; large pads plus inter-cell barriers mandatory | 顶盖排气方向可控,壳面导热好,热蔓延最容易设计Directional venting, good can conduction — easiest propagation design | 点接触散热差,需导热胶灌封;单体小但数量多,蔓延路径复杂Point contact, needs potting; small cells but many paths | 大面贴合冷板,平面导热好;热蔓延沿长边传播,需分段阻断Large faces bond to cold plates; long-edge propagation must be segmented and blocked |
| 典型失效模式Failure modes | 鼓包、漏液、极耳撕裂、铝塑膜被毛刺刺穿Swelling, leakage, tab tear, film puncture by burrs | 防爆阀开启后喷发、顶盖焊点失效、壳体绝缘破损Vent actuation, cap weld failure, can insulation breach | 焊点虚焊发热、CID 误动作、单体一致性差导致组内失衡Cold welds heating, CID nuisance trip, imbalance from cell scatter | 长壳体制造公差、极柱焊接、涂胶失效、长边热扩散Long-can tolerances, terminal welding, adhesive failure, long-edge propagation |
| PACK 工艺复杂度PACK complexity | 高 — 热熔胶 / 侧板 / 膨胀管理,设备投入大High — adhesive, side plates, swell management, capex-heavy | 中 — 螺栓 / 铜排 / 激光焊成熟,产线最容易搭Medium — mature bolting, busbars, laser welding | 高 — 点焊工位多、支架模具费、采样线束最复杂High — many weld stations, jig tooling, most harness work | 中低(CTP 零件少),但涂胶、堆叠精度与箱体平面度要求高Low-medium (fewer CTP parts) but tight adhesive, stacking and flatness requirements |
| 防爆 / 耐压适配Ex-proof & pressure | 差。无壳体承压能力,防爆箱场景一般不选Poor — no pressure-containing shell; avoid for Ex enclosures | 好。钢壳方形是防爆箱、矿用、特种主流选择Good — steel prismatic is the standard for Ex, mining, special | 最好。单体承压最高,最多防爆认证采用Best — highest cell pressure rating, most Ex-certified | 一般。长薄壳体承压能力有限,防爆箱场景不优先Moderate — limited pressure capability; not first choice for Ex enclosures |
| 尺寸灵活度Form-factor freedom | 最高,中小容量可按客户箱体贴合定制Highest — small/mid capacity can be tailored to the enclosure | 低,基本只能选厂标尺寸Low — catalogue sizes only | 低,只有固定几种规格Low — fixed standard sizes | 低,长度与厚度固定,适合大平面布置Low — fixed length and thickness, suited to large flat layouts |
| 采购可得性Availability | 中。中小容量充足,大软包靠储能与客车渠道Medium — small cells ample, large pouch via storage/bus channels | 最好。280/314Ah 储能款现货充分Best — 280/314 Ah storage cells in stock | 最好。18650/21700 现货最多,急单首选Best — 18650/21700 most stocked, ideal for rush orders | 中。以铁锂刀片为主,储能与车企渠道主导Medium — mostly LFP blade, led by storage and OEM channels |
| 弘柏适配建议HONGBAI recommendation | 适合尺寸 / 重量敏感的定制箱与水下充油耐压方案,须自建软包压紧结构工艺For size/weight-critical custom boxes and oil-compensated subsea packs; requires in-house pouch clamping know-how | 作为默认推荐形态:交付最快、认证最顺、返修率最低Default choice — fastest delivery, smoothest certification, lowest return rate | 适合工具 / 机器人 / 无人机等高倍率小容量与急单;报价须计入点焊工位数与支架模具For high-rate, low-capacity and rush work (tools, robots, drones); price in weld stations and jig tooling | 适合大容量平面布置的储能与商用车底盘(CTP);小批量、异形与小体积场景不推荐For large flat ESS and commercial-vehicle chassis (CTP); not advised for small lots, irregular or compact layouts |
STEP 2 · COLD & RATE
磷酸铁锂 0℃ 以下基本不可充电,这是材料特性不是缺陷;北方、冷库与户外夜充必须配 PTC/硅胶加热膜与低温 BMS 策略(加热功率按 0.1–0.15C 设计)。钛酸锂是唯一在 -30℃ 仍可充电的量产体系。LFP is essentially non-chargeable below 0 ℃ — a material property, not a defect. Cold-climate and freezer duty needs a PTC/silicone heater plus low-temperature BMS logic (sized at 0.1–0.15 C). LTO is the only volume system that still charges at -30 ℃.
| 化学体系Chemistry | -20℃ 放电保持discharge | -40℃ 放电保持discharge | 常规最低可充电Min. charge | 低温配方可充电Low-temp grade | 是否需加热膜Heater needed | 低温方案要点Design notes | 倍率能力Rate |
|---|---|---|---|---|---|---|---|
| LiFePO₄ | 55–70% | 35–50% | 0℃ | -10~-20℃ | 必须Always | 加热膜 + 5–10℃ 温升门槛解锁充电;保温层与低温 BMS 策略缺一不可Heater plus a 5–10 ℃ rise threshold before charge unlock; insulation and low-temp BMS both required | 常规 0.5–1C,高倍率款 3–5C0.5–1 C typical, 3–5 C high-rate |
| NCM | 75–85% | 50–65% | -10℃ | -20~-30℃ | 建议(-10℃ 以下仍需预热才充)Advised (pre-heat below -10 ℃) | 低温电解液配方 + 低阻抗负极;放电侧一般不需加热,冷启动电流大时仍需预热Low-temperature electrolyte and low-impedance anode; discharge usually needs no heating, high cold-crank current does | 常规 1–3C,动力圆柱 5–8C1–3 C, 5–8 C power cylindrical |
| LTO | 70–80% | 45–60% | -30℃ | -40~-50℃ | 多数场景不需要(最大卖点)Usually not — its key selling point | 可整套省掉加热系统与其功耗、失效点;但需按 2.4V/节 重算电压比与成本Removes the whole heating subsystem, its power draw and failure points; recalculate voltage ratio at 2.4 V/cell | 5–20C 持续,30C+ 瞬时5–20 C cont., 30 C+ peak |
| Na-ion | 85–92% | 70–80% | -30℃ | -40℃ | 多数场景不需要Usually not needed | 宽温是核心优势,-40℃ 仍可放电与充电;但电压平台斜率大,SOC 估算须重新标定Wide temperature is the selling point — discharge and charge still work at -40 ℃; the sloped plateau requires new SoC estimation | 1–3C,部分型号 5C1–3 C, some parts 5 C |
| 半固态 / 混合固液Hybrid solid-liquid | 70–85% | 45–60% | -15℃ | 部分型号 -20~-30℃-20 to -30 ℃ on some parts | 北方建议保留Keep for cold regions | 减液不等于无液,低温充电限制仍存在。装车数据:-7℃ 续航达成率约 75%,-25℃ 仍在 60% 以上,属「可预期打折」而非「不衰减」,不要按 -40℃ 可充承诺Reduced electrolyte is not zero electrolyte. Field data: ≈75% range at -7 ℃, still above 60% at -25 ℃ — a predictable discount, not "no derating". Never promise -40 ℃ charging | 1–3C |
| 全固态(硫化物软包)· 仅技术参考Sulfide all-solid-state pouch · reference only | — | — | 宣称可 -30~-40℃ 充电claimed -30 to -40 ℃ | -40℃ | 不需要No | 目前处于中试线阶段(20–60Ah 样品、整包 265–303Wh/kg),无对外零售裸电芯渠道,PACK 厂现阶段不可选型Pilot-line stage (20–60 Ah samples, 265–303 Wh/kg pack). No retail bare-cell channel; not selectable for PACK builders today | 1–10C(样品)1–10 C (samples) |
STEP 3 · FULL MATRIX
表格较宽,可左右滑动查看。金色底为选型最关键列;最右列为中国出口管制风险判定。Wide table — scroll horizontally. Gold columns are decisive; the right-hand column is the China export-control verdict.
| 化学体系Chemistry | 电芯形态Format | 电芯能量密度 Wh/kgCell Wh/kg | 整包能量密度 Wh/kgPack Wh/kg | 循环 次Cycles | 持续倍率Rate | -20℃ 放电保持discharge | 本体安全Intrinsic safety | 市场可得性Availability | 主要工艺与结构风险Key process risk | 典型应用Typical use | 出口管制Export control |
|---|---|---|---|---|---|---|---|---|---|---|---|
| LiFePO₄ | 软包Pouch | 165–210 | 125–165 | 2500–4500 | 1–3C | 60–70% | ★★★★☆ | 中小容量充足;50Ah 以上大软包以储能与客车厂自供为主,外销渠道窄Small/mid ample; >50 Ah mostly captive to storage and bus OEMs | 铝塑膜易被极片毛刺刺穿;循环鼓包须预留 2–3mm 间隙;无边框,PACK 须提供整体侧向约束Film puncture by burrs; allow 2–3 mm swell; PACK must supply full side constraint | AGV/RGV、低速车、观光车、高尔夫球车、便携储能、尺寸敏感定制箱AGV/RGV, low-speed and sightseeing vehicles, golf carts, portable power, size-critical boxes | 否No |
| LiFePO₄ | 方形(铝壳 / 钢壳)Prismatic (Al / steel) | 150–190 | 110–145 | 3000–8000 | 0.5–1C | 55–68% | ★★★★☆ | 最好买。280/314Ah 通用于储能,50–173Ah 通用于动力,B/C 样渠道成熟Easiest to source; 280/314 Ah storage and 50–173 Ah power are catalogue parts | 防爆阀一致性由电芯厂控制;PACK 端铜排载流与螺栓力矩是主要失效点;钢壳款适合防爆箱,铝壳需绝缘Vent consistency is the cell maker's job; busbar ampacity and bolt torque dominate PACK failures | 家储、工商业储能、通讯基站、UPS、大型电动叉车、轨道车辆Home and C&I storage, base stations, UPS, large forklifts, rail | 否No |
| LiFePO₄ | 圆柱(含全极耳)Cylindrical | 140–175 | 95–125 | 2000–4000 | 2–5C | 60–70% | ★★★★☆ | 充足,但同容量电芯数量多,PACK 设计余量小Ample, but many cells per kWh — little design slack | 单体数量大 → 焊点、采样线束、一致性管理成本最高;全极耳需专用点焊与支架模具Most welds, taps and matching work; tabless needs dedicated jigs and welding | 电动工具、两轮三轮、便携储能、太阳能路灯、UPS、中小容量 AGVPower tools, e-bikes, portable power, street lights, UPS, small AGV | 否No |
| LiFePO₄ | 刀片Blade | 160–195 | 135–170 | 3000–6000 | 0.5–1C | 55–68% | ★★★★☆ | 中;铁锂刀片以储能与车企自供为主,散购渠道有限Medium; mostly captive to storage and OEM channels | 长壳体制造公差、涂胶与堆叠平面度、长边热扩散;PACK 端需精密平面度控制Long-can tolerances, adhesive and stacking flatness, long-edge propagation; tight pack flatness | 储能集装箱、商用车底盘、大型平面电池仓、CTP 集成包ESS containers, CV chassis, large flat bays, CTP packs | 否No |
| NCM | 软包Pouch | 210–280 | 160–225 | 800–2000 | 1–3C | 75–85% | ★★★☆☆ | 3C 消费 / 轻型动力软包充足;高镍大软包主要供车用,外销少Consumer and light-mobility pouch ample; Ni-rich automotive cells rarely sold out | 高温存储产气鼓包;成组必须留膨胀通道与导热垫;单体间需隔热片阻断热扩散Gas generation and swelling in hot storage; needs swell channels, pads and inter-cell barriers | 无人机、eVTOL、高端便携电源、重量敏感 AGV、医疗便携设备Drones, eVTOL, premium portable, weight-critical AGV, medical portable | 看型号 — 高镍高容量款易越 300Wh/kg 线Part-dependent — Ni-rich grades can cross 300 Wh/kg |
| NCM | 方形Prismatic | 180–240 | 135–180 | 1200–2500 | 1–3C | 70–80% | ★★★★☆ | 车规电芯对外流通极少,实际可选主要是二线厂方形与库存Automotive cells rarely sold out; mainly second-tier parts and stock | 模组结构原本依赖电芯厂托盘;散购时 PACK 须自建端板与压紧机构Usually sold with an OEM tray; loose purchase needs custom end plates and preload | 低速车、轨交辅助电源、UPS、体积受限的工业设备Low-speed vehicles, rail auxiliary, UPS, volume-limited industrial | 否No |
| NCM | 18650 / 21700 / 46 系列series | 230–300 | 150–210 | 500–1500 | 2–5C | 75–85% | ★★★☆☆ | 最充足、现货最好、样品最快,适合急单与小批量Most available, fastest samples — ideal for rush and small lots | 循环最短、单体与焊点最多;长期大电流下镍带发热是主要失效模式;支架模具费高Shortest life, most welds; strap heating under sustained current; costly jigs | 电动工具、园林工具、机器人、轻量化便携电源、无人机(高倍率款)Power and garden tools, robots, light portable power, drones (high-rate) | 看型号 — 21700 高容量款已接近 300Wh/kgPart-dependent — high-capacity 21700 nears 300 Wh/kg |
| NCM | 刀片Blade | 200–240 | 160–200 | 1000–2000 | 1–2C | 70–80% | ★★★☆☆ | 少,多为车企定制,对外流通有限Rare; mostly OEM-directed | 高镍长电芯的产气与热蔓延控制、制造精度要求最高Gassing and propagation control plus precision are hardest on long Ni-rich cells | 高端乘用车、特种底盘、航空地面设备Premium EV, special chassis, aviation ground equipment | 看型号 — 高镍款可能越 300Wh/kgPart-dependent — Ni-rich grades may exceed 300 Wh/kg |
| LTO | 软包Pouch | 80–105 | 60–80 | 10000–25000 | 5–10C | 70–80% | ★★★★★ | 紧俏,全球供应商少、单价高、交期常 12 周以上Scarce — few suppliers, long lead, often 12+ weeks | 放电平台约 1.7V、充电上限 2.8V,必须按 3S1P≈8.4V 的电压比重算整机;LTO 产气需内涂层与排气设计Plateau ≈1.7 V, charge max 2.8 V — re-derive system voltage (3S1P ≈ 8.4 V); gassing needs coated film and venting | 快充调频储能、港口 RTG/AGV 机会充电、汽车启停、特种、极寒设备Frequency regulation, port RTG/AGV opportunity charging, start-stop, special, arctic | 否No |
| LTO | 方形Prismatic | 75–100 | 55–75 | 10000–30000 | 5–10C | 70–80% | ★★★★★ | 紧俏,主要由专门厂定生产,无现货Scarce — made to order by specialist plants | 金属壳产气控制优于软包,适合长寿命户外与柜内安装;单体重、连接件少Metal can controls gassing better than pouch; heavy cells but fewer connections | 轨交再生制动、油田矿山快充、船舶直流组网、军用方舱Rail regenerative braking, mine and oil-field fast charge, DC ship grids, special shelters | 否No |
| LTO | 18650 / 21700 圆柱cylindrical | 65–95 | 45–65 | 10000–20000 | 10–20C | ~70% | ★★★★★ | 紧俏,容量小、成组数量多Scarce; small capacity means many cells | 超大倍率下焊点发热严重,须用全极耳或加厚镍带并做温升仿真Weld heating dominates at extreme rates — use tabless or heavy straps plus thermal simulation | 启动电源、高倍率工具、医疗设备、航天地面设备Jump starters, high-rate tools, medical, ground support equipment | 否No |
| Na-ion | 软包Pouch | 110–150 | 80–115 | 2000–4000 | 1–3C | 85–90% | ★★★★☆ | 少,样品与小批为主Scarce — samples and small lots | 产气与封装可靠性、硬碳批次一致性;电压窗口窄,BMS 阈值需重标Gassing, sealing reliability and hard-carbon consistency; narrow window needs new BMS thresholds | 便携备电、宽温设备、特种电源Portable backup, wide-temperature gear, special power | 否No |
| Na-ion | 方形Prismatic | 100–150 | 75–115 | 3000–6000 | 0.5–2C | 85–90% | ★★★★☆ | 起量中,储能款为主Ramping up, mainly storage grades | 产气与批次一致性;能量密度低,同容量箱体更大Gassing and consistency; lower density means larger enclosures | 储能、低速车、通讯基站、备电ESS, low-speed vehicles, base stations, backup | 否No |
| Na-ion | 26700 / 32140 圆柱cylindrical | 90–130 | 65–95 | 2000–4000 | 2–5C | 85–92% | ★★★★☆ | 中,规格少、供应商集中Medium; few sizes, concentrated supply | 焊点与一致性管理;能量密度低导致电芯数量多Welds and matching; low density means more cells | 两轮车、电动工具、备电、宽温设备Two-wheelers, tools, backup, wide-temperature gear | 否No |
| Na-ion | 刀片Blade | 95–140 | 70–110 | 3000–6000 | 0.5–2C | 85–90% | ★★★★☆ | 样品与小批,示范项目为主Samples and pilots, demonstration projects | 长壳体产气与封装、量产一致性待验证Gassing and sealing on long cans; production consistency unproven | 储能示范、大型平面备电Pilot ESS, large flat backup | 否No |
| 半固态 / 混合固液Hybrid solid-liquid | 软包Pouch | 300–400 | 230–310 | 800–2000 | 1–3C | 70–85% | ★★★★☆ | 样品 / 小批量可谈,需签定向采购或联合开发协议;优先供应车企,PACK 厂拿货门槛高Samples and small lots negotiable under directed purchase or a JDA; OEMs take priority, hard for PACK builders | 多数仍保留注液工序;PACK 须预留更大膨胀补偿与更严的加压均匀性;务必要求电芯厂书面承诺循环与质保条款Mostly still liquid-filled; needs larger swell compensation and far tighter preload uniformity — insist on written cycle and warranty terms | 无人机 / eVTOL、潜航器与 AUV、高端便携电源、豪华电动车Drones and eVTOL, AUV and USV, premium portable power, luxury EV | ⚠ 是 — 电芯 ≥300Wh/kg 落入管制清单⚠ Yes — cells ≥300 Wh/kg are listed |
| 半固态 / 混合固液Hybrid solid-liquid | 方形Prismatic | 260–360 | 195–265 | 1500–3000 | 0.5–2C | 65–80% | ★★★★☆ | 方形是半固态最成熟的量产形态(与现有产线兼容 70–80%),可对接性最好The most mature semi-solid format — 70–80% line compatibility, easiest to engage | 固-固界面需外部约束压力,端板刚性与压紧力矩必须精确控制,不能沿用常规方形 PACK 图纸Solid-solid interfaces need external preload — end-plate stiffness and torque must be re-engineered, not copied | 工商业储能高端版、车规、基站备电、轨道交通Premium C&I storage, automotive, base-station backup, rail | 看型号 — 300Wh/kg 以上即触发Part-dependent — triggers above 300 Wh/kg |
| 半固态 / 混合固液Hybrid solid-liquid | 圆柱Cylindrical | 250–320 | 170–225 | 1000–2000 | 2–5C | 70–80% | ★★★★☆ | 少见,多数以样品 / 定向供货为主Rare — mostly samples or directed supply | 需定制支架与点焊工艺;电芯厂公开资料稀缺,须逐款索取针刺 / 热箱 / 过充第三方报告Custom jigs and welding; datasheets are scarce — demand nail, hot-box and overcharge reports per part | 无人机高比能包、便携电源、特种装备High-energy drone packs, portable power, special equipment | 看型号 — 接近或超过 300Wh/kgPart-dependent — at or above 300 Wh/kg |
注:本表未列出「单体标称电压」「标称容量档位」「成组效率」三列(电压:铁锂 3.2V / 三元与半固态 3.6–3.7V / 钛酸锂 2.4V;成组效率见上方形态表)。完整列版资料可在 索取 Excel 选型工具 时一并提供。Note: nominal voltage, capacity tiers and utilisation columns are omitted (3.2 V LFP, 3.6–3.7 V NCM and hybrid, 2.4 V LTO; utilisation appears in the format table above). The full column set is available on request.
STEP 4 · CHEMISTRY
单体电压:铁锂 3.2V / 三元与半固态 3.6–3.7V / 钠离子 3.0–3.1V / 钛酸锂 2.4V。钛酸锂平台电压低,同电压需更多串联数,BMS 与成本同步上升;钠电电压窗口与锂电不同,BMS 阈值须重新标定。钴酸锂、锰酸锂主要出现在小型消费与工具电芯,见文末附注。Nominal voltage: 3.2 V LFP, 3.6–3.7 V NCM and hybrid, 3.0–3.1 V Na-ion, 2.4 V LTO. LTO's low plateau needs more series cells; Na-ion has a different voltage window and needs recalibrated BMS thresholds. LCO and LMO mainly appear in small consumer and tool cells — see the note at the end.
| 化学体系Chemistry | 定位Positioning | 电芯能量密度 Wh/kgCell energy Wh/kg | 循环寿命 次Cycle life | 持续倍率Continuous rate | 最适合的场景Best fit | 必须接受的代价Price you pay |
|---|---|---|---|---|---|---|
| 磷酸铁锂 LiFePO₄ | 成本与寿命之王King of cost & cycle life | 150–210 | 3000–8000 | 0.5–3C(高倍率款 5C) | 家储、工商业储能、基站、UPS、AGV、叉车、低速车、太阳能路灯Home & C&I storage, base stations, UPS, AGV, forklifts, low-speed vehicles, solar street lights | 低温最差,能量密度最低,电压平台平导致 SOC 难估Worst cold performance, lowest energy density, flat plateau makes SoC hard to estimate |
| 三元 NCM | 能量密度与低温主力Energy density & cold-weather workhorse | 180–300(高镍 330+) | 800–2500 | 1–5C(高倍率 8C) | 无人机、eVTOL、潜航器、便携电源、高端 AGV、医疗设备Drones, eVTOL, AUV/USV, portable power, premium AGV, medical devices | 循环短、成本高、热失控起始约 200℃,需强化热扩散抑制Shorter life, higher cost, onset ≈200 ℃ — needs stronger propagation suppression |
| 钛酸锂 LTO | 快充与极寒之王Fast-charge & extreme-cold champion | 65–105 | 10000–30000 | 5–20C 持续,30C+ 瞬时 | 汽车启停、港口机会充电、特种方舱、轨交再生制动、极寒设备Start-stop, port opportunity charging, special shelters, rail regenerative braking, arctic equipment | 贵 5–10 倍,能量密度只有铁锂一半,需重算串联数5–10× cost, half of LFP energy density, series count must be recalculated |
| 钠离子 Na-ion | 资源自主 + 宽温Resource independence & wide temperature | 100–160 | 2000–6000 | 1–5C | 储能、低速车、两轮车、基站备电、宽温设备ESS, low-speed vehicles, two-wheelers, base-station backup, wide-temperature gear | 能量密度低于锂电、产业链仍在爬坡、产气与硬碳批次一致性需验证;电压窗口不同,BMS 阈值须重标Lower energy density, still ramping supply chain, gassing and hard-carbon consistency to verify; different voltage window needs recalibrated BMS thresholds |
| 半固态 / 混合固液 | 高比能 + 高安全冗余High specific energy + safety margin | 260–400(样品 480+) | 800–3000(数据积累中) | 1–3C(部分样品 5C) | 无人机 / eVTOL、潜航器与 AUV、特种、高端便携电源Drones / eVTOL, AUV & USV, special-purpose power, premium portable | 约 3 倍成本、产能紧张、长期可靠性样本不足、≥300Wh/kg 受出口管制≈3× cost, tight capacity, limited field data, ≥300 Wh/kg falls under export control |
附注:钴酸锂 LCO 与锰酸锂 LMO 主要做成小容量软包 / 圆柱,集中在数码、消费电子、电动工具与两轮车;比能量或高温循环是短板,大批量 PACK 项目通常不作为首选,本表不单列组合。Note: LCO and LMO are mostly built as small pouch or cylindrical cells for consumer electronics, power tools and two-wheelers. They trail on volumetric energy or high-temperature cycling, so large PACK programmes rarely choose them; they are not listed as separate combinations here.
BY APPLICATION
覆盖弘柏十条主力方向:智能仓储、大型叉车、低速车、低空飞行器、潜航器与无人船、轨道交通、便携与户用储能、电动工具与机器人、启停与特种。Covering HONGBAI's ten main directions: warehousing, large forklifts, low-speed vehicles, low-altitude aircraft, AUV/USV, rail, portable and residential storage, tools and robotics, start-stop and special power.
| # | 应用领域Application | 关键工况约束Duty constraints | 推荐体系Chemistry | 推荐形态Format | 备选Alternative | PACK 端重点设计项PACK focus | 认证 / 合规提示Compliance |
|---|---|---|---|---|---|---|---|
| 01 | AGV / RGV / 智能仓储AGV / RGV / warehousing | 24/48/72/80V | 磷酸铁锂LiFePO₄ | 方形(优先)/ 软包Prismatic (first) / pouch | 三元(重量受限或冷库)NCM if weight-limited or freezer duty | 循环寿命与充电策略优先;CAN/RS485 对接整机调度;快充场景配加热膜与温度降额Life and charge strategy first; CAN/RS485 to fleet control; heater plus derating for fast charge | UN38.3 + CE;欧盟注意电池法 2027-02-18 标签与碳足迹节点UN38.3 + CE; EU Battery Regulation labelling and carbon footprint by 18 Feb 2027 |
| 02 | 大型电动叉车 / 港口 RTGLarge forklift / port RTG | 80V/800Ah+ | 磷酸铁锂(高倍率款)LFP, high-rate grade | 方形(钢壳利于防爆)Steel prismatic (Ex-friendly) | LTO | 铜排载流与温升、紧固力矩、换电机构与防撞、大电流接触器与熔断器选型Busbar ampacity and heating, torque, swap mechanics and impact protection, contactor and fuse sizing | CE / EN 1175(工业车辆电气安全)、EN 61373 类振动考核CE / EN 1175 plus rail-grade vibration screening |
| 03 | 低速车 / 观光车 / 高尔夫球车Low-speed / sightseeing / golf cart | 36–72V | 磷酸铁锂LiFePO₄ | 方形 / 圆柱 32140Prismatic / 32140 | 三元(续航 >150km)NCM if range >150 km | IP65 以上箱体、北方低温加热、充电器协议匹配、并机扩容IP65+ enclosure, heater for cold regions, charger protocol match, parallel expansion | 美国 UL 2271 / UL 2580;欧盟 EN 15194(EPAC)或整车 L6 类别UL 2271 / UL 2580 in North America; EN 15194 or L6 in the EU |
| 04 | 无人机 / eVTOL / 低空飞行器Drone / eVTOL | 重量第一、5–10C 爆发、高空低温、坠落安全weight first, 5–10 C bursts, cold altitude, crash safety | 高镍三元软包Ni-rich NCM pouch | 软包(唯一合理选择)Pouch — the only sensible choice | 半固态软包(>300Wh/kg)semi-solid pouch above 300 Wh/kg | 成组效率每提高 1% 直接换航时;必须做热扩散抑制与单向泄压;高空低气压散热仿真Every 1% of utilisation becomes flight time; propagation suppression and directional venting mandatory; low-pressure cooling simulation | ⚠ 电芯 ≥300Wh/kg 落入出口管制清单;无人机整机另受无人机出口管制约束,须逐单核查⚠ Cells ≥300 Wh/kg are export-controlled; drone platforms carry separate controls — screen case by case |
| 05 | 潜航器 AUV / 无人船 / 水下机器人AUV / USV / underwater robot | 海水不可压缩、充油压力平衡、长期浸泡incompressible seawater, oil compensation, long immersion | 磷酸铁锂(寿命)/ 三元软包(体积)LFP for life / NCM pouch for volume | 软包(充油补偿结构最成熟)Pouch — mature with oil compensation | 半固态软包(安全 + 体积双敏感)semi-solid pouch when both matter | 充油式耐压平衡结构、软包膨胀余量与油路补偿、灌封与耐压舱密封、K 值与自放电筛选、防腐蚀端子Oil-compensated pressure balancing, swell allowance matched to oil volume, potting and hull sealing, K-value and self-discharge screening, corrosion-proof terminals | UN38.3 + 运输条件鉴定书;涉海 / 特种客户可能要求船级社(CCS/DNV)与军标配套UN38.3 plus transport appraisal; naval and special clients may require CCS/DNV class and special standards |
| 06 | 轨道交通辅助 / 牵引电源Rail auxiliary / traction | -25~50℃ | 磷酸铁锂 / LTOLFP / LTO | 方形(钢壳)Steel prismatic | 半固态方形semi-solid prismatic | EN 50155 温度 / 振动 / 供电中断等级、EN 45545 防火、冗余与隔离设计、远程监控EN 50155 temperature, shock and supply-interruption classes; EN 45545 fire; redundancy, isolation, remote monitoring | EN 50155 + EN 45545-2 + EN 61373;欧盟强制,取证周期 6–12 个月Mandatory in the EU; 6–12 months to certify |
| 07 | 便携储能 / 户外电源Portable power station | 1–3kWh | 磷酸铁锂(循环)/ 三元(轻小)LFP for cycles / NCM for weight | 方形 / 圆柱 21700Prismatic / 21700 | 软包(超薄形态)Pouch for ultra-thin profiles | AC 逆变一体安全、提手与堆叠、100Wh 航空限制说明、APP / 蓝牙、PD / QC 快充协议Integrated inverter safety, handle and stacking, 100 Wh air-travel guidance, app and Bluetooth, PD/QC | 美国 UL2743 + FCC + Prop 65;UN38.3 + 航空 PI966/967;欧盟 CE + WEEE + 电池法UL2743, FCC, Prop 65; UN38.3 with PI966/967; CE, WEEE, EU Battery Regulation |
| 08 | 家储 / 工商业储能 / 路灯 / 基站 / UPSHome and C&I storage, street light, base station, UPS | 5–15 | 磷酸铁锂LiFePO₄ | 方形 50–314AhPrismatic 50–314 Ah | 圆柱 32140(小容量户储)32140 for small home units | 消防与热失控蔓延抑制、簇级并联与环流、液冷 / 风冷、并离网切换、RS485/CAN 对接 PCSFire and propagation control, cluster parallel and circulating current, cooling, on/off-grid transfer, RS485/CAN to PCS | IEC 62619 + IEC 63056 + UL 1973;美国大型储能另需 UL 9540/9540A;IRA/FEOC 追溯电芯与原产地IEC 62619, IEC 63056, UL 1973; US grid storage also UL 9540/9540A; IRA/FEOC traces cell origin |
| 09 | 电动工具 / 机器人 / 医疗便携Power tools / robotics / medical portable | 10–20C | 三元圆柱 21700(动力型)21700 NCM power | 圆柱Cylindrical | LTO(超瞬时)/ 软包(厚度极敏感)LTO for extreme peaks / pouch for thin profiles | 全极耳或加厚镍带、单体温升仿真、防跌落缓冲、高一致性配电芯Tabless or heavy straps, per-cell thermal simulation, drop buffering, tightly matched cells | IEC 62133-2 + UN38.3;医疗另走 IEC 60601-1;欧盟 MDR 附带电池法要求IEC 62133-2 + UN38.3; medical adds IEC 60601-1; EU MDR plus Battery Regulation |
| 10 | 汽车启停 / 特种 / 极端温度特种Start-stop / special / extreme temperature | -40℃ | LTO | 方形(钢壳利于防爆方舱)Steel prismatic for Ex shelters | 三元低温软包 / 半固态low-temp NCM pouch / semi-solid | 超宽温设计、防爆与抗毁伤结构、EMC、长存储寿命与自放电管理Wide-temperature design, blast and damage tolerance, EMC, long shelf life and self-discharge control | GJB 150A / 181B / 450A 等军标体系;保密项目走专用渠道,不参与一般贸易GJB 150A / 181B / 450A families; classified programmes run through dedicated channels |
CERTIFICATION · MAINLAND FIRST
我们主要服务中国内陆客户,所以下表以国内强制标准为纲;海外认证仅在客户整机需要出口时才适用,已排到表末。弘柏可协助送检与资料准备,最终清单取决于客户目的市场与终端用途。We mainly serve mainland Chinese customers, so the table below leads with domestic mandatory standards; overseas certification applies only when the customer's machine is exported and sits at the end. HONGBAI assists with testing and documentation; the final list depends on destination and end use.
| 类别Category | 标准 / 法规Standard | 是否强制Mandatory | 周期与费用量级Lead time & cost | 实操要点Practical notes |
|---|---|---|---|---|
| ★ 储能安全(首部强标)★ Storage safety (first mandatory standard) | GB 44240-2024 / GB/T 36276-2023 / GB/T 42288 | 强制Mandatory | 电芯由电芯厂持证,PACK 端配合送检cell maker holds it; PACK builder supports testing | 覆盖电信、中央应急照明与报警、固定式启动、光伏与大容量储能等场景;电芯层新增振动、加速冲击、浅刺(Φ5mm 钢针刺入 10mm 或厚度 30%,1h 不起火不爆炸)、强制放电,过充加严为 1.5 倍限制电压后恒压 1h。选电芯时先索取该标准检测报告或证书编号,再谈价格。Covers telecom, central emergency lighting and alarms, fixed engine start, PV and bulk storage. New cell-level vibration, acceleration-shock, shallow-needle (Φ5 mm, 10 mm or 30% depth, 1 h no fire) and forced-discharge tests; overcharge tightened to 1.5× limit voltage held 1 h. Ask for the report or certificate number before discussing price. |
| ★ 移动电源 / 便携储能 3C★ Mobile power CCC | GB 47372-2026 + GB 31241-2022 + GB 4943.1-2022 | 强制(CCC)Mandatory (CCC) | 过渡至 2027-04-01 全面执行full enforcement 1 Apr 2027 | 品类划分是第一步:0914 移动电源(充电宝、便携式储能)、0915 便携式电子产品用锂电、0916 移动电源专用锂电。同一企业不得把 0915 电池套用至移动电源。新规增加漏液强制抽检(型式试验、生产现场与市场抽检全环节)、针刺与循环老化后析锂检测,并要求专属编码与安全使用年限标注。旧证书须在 2027-04-01 前完成转换。Classification comes first: 0914 mobile power (power banks, portable stations), 0915 cells for portable electronics, 0916 cells for mobile power. One company may not use 0915 cells in mobile power products. New rules add mandatory leaktightness sampling across type testing, factory and market, plus nail tests and lithium-plating checks after cycle ageing, unique codes and a declared safe-use life. Old certificates must be converted by 1 Apr 2027. |
| ★ 电动自行车 / 换电 3C★ E-bike and swap CCC | GB 43854-2024 + GB 17761-2024 | 强制Mandatory | 证书有效期 5 年,证后监督趋严5-yr validity, tighter surveillance | 「一车一池一充一码」:整车、电池、充电器各赋唯一码并绑定,禁止裸车出厂;电池须与充电器、控制器做充放电互认,BMS 从被动保护芯片升级为主动身份节点。编码要求耐 950℃ 高温火灾后仍可溯源。做两轮线必须先回答「能不能握手」。One-vehicle-one-battery-one-charger-one-code: unique bound codes for all three, no bare vehicle ex-works; the battery must authenticate with charger and controller, turning the BMS from a passive protector into an active identity node. Codes must survive 950 ℃. For two-wheeler work, answer "can it hand-shake" first. |
| 车用动力电池EV traction battery | GB 38031-2025 / GB 18384-2025 | 强制(上车的车型)Mandatory when vehicle-mounted | 试验成本高,需提前排期costly tests, plan early | 热失控由「报警 5 分钟」升级为观察期内不起火不爆炸;新增底部撞击(Φ30mm 撞头 150J 连续 3 次)与 15 分钟快充循环 300 次后的外部短路;GB 18384-2025 要求高压回路物理断开「一键断电」。场内车、特种车、无人平台整车客户会拿这条问我们,适用性不确定时页面写「需按车型与主管部门口径确认」,不要硬套。Thermal runaway upgraded from a 5-minute alarm to no fire within the observation window; new bottom impact (Φ30 mm, 150 J, three hits) and short-circuit after 300 fast-charge cycles; GB 18384-2025 requires a physical high-voltage disconnect. Site vehicles, special vehicles and unmanned platforms will ask — where applicability is unclear, state "subject to vehicle type and authority interpretation" rather than over-claim. |
| 固态 / 半固态命名Solid-state naming | GB/T 43568-2026 | 宣传与申报口径wording for claims | — | 电解液质量占比 >20% 为液态;5%–20% 为「混合固液电池」(即俗称半固态);低于 5% 且通过 120℃ 真空 6h、失重率 ≤0.5% 才可称「全固态」。全站对外表述统一按此,不要出现「固态 / 全固态」的模糊用法。Above 20% electrolyte by mass is liquid; 5–20% is a hybrid solid-liquid cell; only below 5%, passing 120 ℃ vacuum 6 h at ≤0.5% loss, may be called all-solid-state. Use this wording everywhere. |
| 电动摩托车锂电E-motorcycle lithium | GB 36672-2026 | 即将强制becoming mandatory | 建议 2027 上半年前完成准备prepare by H1 2027 | 电摩用锂离子电池由推荐性升为强制性;配套还有 GB 47371-2026 充电桩强标(2027-04-01)与 GB/T 47265-2026 电子身份(2026-10-01)。E-motorcycle lithium cells move from recommended to mandatory; related: GB 47371-2026 charging-pile standard (1 Apr 2027) and GB/T 47265-2026 electronic identity (1 Oct 2026). |
| 防爆 / 矿用Explosion-proof / mining | GB/T 3836 系列 / 矿用安全标志mining safety mark MA·KY | 强制(相应场景)Mandatory for those uses | 取证周期长、费用高long and costly | 防爆箱场景优先选钢壳方形或圆柱,软包本体无承压能力一般不选;无 Ex 证书前页面只写「配合客户取证」,不要写「可做防爆电池」。Ex enclosures favour steel prismatic or cylindrical cells — pouch has no pressure rating. Until certified, say "we support the customer's certification", not "we make Ex batteries". |
| 船舶与轨道Marine & rail | CCS 中国船级社China Classification Society / TB 系列铁路标准railway standards | 入级与检验要求class and inspection | 与船检 / 主机厂同步推进run in parallel with class | 电动船舶客户的第一个问题往往是「能不能过船检」;把取证流程、需要客户提供的资料与周期写成 FAQ,是被搜索也被客户信任的内容。Electric-ship buyers ask about class approval first. Write the approval path, required documents and timeline as an FAQ — it is searched and it builds trust. |
| 医疗器械Medical devices | GB 9706.1-2020 | 强制(注册)Mandatory for registration | 随整机注册follows device registration | 重点在一致性、可追溯与失效保护:K 值全检、内阻与开路电压 100% 检测、全生命周期追溯记录,这些能力要写成可核验的事实句,而不是「品质可靠」。Consistency, traceability and fault protection matter: 100% OCV, internal-resistance and K-value screening plus full life-cycle trace records — state them as verifiable facts, not "reliable quality". |
| 特种(脱敏)Special (sanitised) | GJB 150A / 181B / 450A 等and related | 按项目要求per programme | — | 涉密项目不进入任何公开内容与信源;官网只写能力与合规边界(宽温、防爆、长存储、EMC),不写型号、客户与参数。Classified programmes never enter public content. The site states capability and boundaries only (wide temperature, blast, shelf life, EMC) — no part numbers, customers or parameters. |
| 运输(内销同样适用)Transport (domestic too) | UN38.3 + 试验概要test summary | 强制Mandatory | 2–4 周2–4 weeks | 国内航空与公路运输同样要求;按电芯型号归系列,改电芯或改串联数须重测。另:2025-06-28 起无 CCC 标志的充电宝禁止乘坐境内航班,可直接作为便携储能卖点。Required for domestic air and road as well; cells are grouped into series, so a cell or series change voids the report. Also, since 28 Jun 2025 power banks without a CCC mark may not be carried on domestic flights — a usable selling point for portable power. |
| 回收与溯源(前瞻)Recycling & traceability | 新能源汽车废旧动力电池回收和综合利用管理暂行办法EV battery recycling measures | 逐步落地phasing in | — | 动力电池「数字身份证」以 24 位编码贯穿单体、模块与电池包,记录基础、运维与回收共 96 项信息;两轮车侧同步走「一车一池一充一码」。做长周期供货要提前把编码与追溯体系设计进 BMS 与产线。The EV battery "digital identity" uses a 24-digit code across cell, module and pack covering 96 fields of base, service and recycling data; two-wheelers follow the same one-battery-one-code path. Design coding and traceability into the BMS and line early for long-life supply. |
| 海外认证(按需)Overseas (on demand) | IEC 62133-2 / UL 2271 / UL 2580 / UL 1973 / UL 9540A / EN 1175 / EN 50155 / EU 2023/1542 | 仅整机出口时only when the machine is exported | 4–24 周,费用差异大4–24 weeks, wide cost range | 客户的整机若出口,认证会顺着供应链传到你身上。欧盟新电池法 2027-02-18 起标签强制、便携式电池须可安全取出更换,超过 2kWh 工业电池须配电池护照。建议在国内页面留一段「出口适配」,让客户知道我们能配合。If the customer's machine is exported, certification flows down the chain. EU Battery Regulation 2023/1542 mandates labelling from 18 Feb 2027, safe removal and replacement of portable batteries, and a Battery Passport for industrial batteries above 2 kWh. Keep a short "export compatibility" note so customers know we can support it. |
| 附注:中国出口管制Note: China export control | 商务部、海关总署公告 2025 年第 58 号MOFCOM & GACC Announcement No. 58 of 2025 | 仅出口时触发only on export | 恢复后许可 60–75 个工作日60–75 working days once reinstated | 列管物项:重量能量密度 ≥300Wh/kg 的锂离子电池(含按整包判定的成品电池包)、高压实磷酸铁锂与富锂锰基正极、人造石墨负极、叠片 / 注液 / 化成分容等设备与技术。当前处于暂停实施期,2027-01-10 到期后是恢复、再延还是取消未定。客户整机要出口、或做无人机与 eVTOL 高比能包时,才需要认真核这一条。Listed items: lithium-ion batteries at ≥300 Wh/kg (finished packs judged at pack level), high-compaction LFP and lithium-rich manganese cathodes, artificial-graphite anodes, and stacking / filling / formation equipment and technology. Currently suspended; the outcome after 10 Jan 2027 is unpublished. This only matters when the customer exports or builds high-energy drone and eVTOL packs. |
EXPORT CONTROL · DETAIL
我们的客户主要在中国内陆,本节不是选型的第一道门槛;但当客户的整机要出口、或做无人机与 eVTOL 高比能包时,它会直接决定交期,务必在报价前核对。法规:商务部、海关总署公告 2025 年第 58 号。Our customers are mostly on the mainland, so this is not the first gate — but when the customer's machine is exported, or for high-energy drone and eVTOL packs, it drives lead time. Regulation: MOFCOM and GACC Announcement No. 58 of 2025.
涉及 ≥300Wh/kg 电芯或整包的订单,建议在合同中加入「因出口管制审批导致交期延后不视为供方违约」条款,并把许可申请所需资料(最终用户、最终用途、生产设施信息)列为客户配合项。For any order involving cells or packs at ≥300 Wh/kg, add a clause stating that delay from export-licence review is not a supplier default, and list end-user, end-use and facility information as customer obligations.
OVERSEAS MARKET ACCESS
我们主要服务中国内陆客户,此表作为客户整机出口时的备查清单;国内强制标准请看上一节。弘柏可协助送检与资料准备,最终清单取决于客户目的国、产品形态与终端用途。We mainly serve mainland customers; keep this as a checklist for export programmes — see the previous section for domestic mandatory standards. HONGBAI assists with testing and documentation; the final list depends on destination market, product form and end use.
| 类别Category | 标准 / 法规Standard | 是否强制Mandatory | 周期与费用量级Lead time & cost | 实操要点Practical notes |
|---|---|---|---|---|
| 运输(全球通用)Transport (global) | UN38.3 | 强制Mandatory | 2–4 周weeks / 0.8–3万元 RMB | 所有锂电池与电池组空海陆运的前置条件;按电芯型号归系列,同系列可覆盖多个 PACK 型号,改电芯或改串联数须重测Precondition for all air, sea and land freight; cells are grouped into series so one report covers several PACKs, but a cell change or series change voids it |
| 运输单据Shipping documents | 运输条件鉴定书 + MSDS/SDSTransport appraisal + MSDS/SDS | 强制Mandatory | 3–7 天days | 货代订舱与报关必附。半固态须如实申报电解液含量,个别货代会走更严格判定 —— 逐票确认,不要写进合同承诺Required for booking and customs. Semi-solid must declare electrolyte content truthfully; some forwarders apply stricter rulings — confirm per shipment, never as a contract term |
| 运输规则Transport rules | PI965–PI968 / IMDG Class 9Class 9 | 强制Mandatory | 随货执行per shipment | 包装、标签、申报单;空运要求荷电状态 SoC ≤30%。批量出货须由持证危险品申报员操作Packing, marks, declarations; air requires state of charge ≤30%. Volume shipments need a certified dangerous-goods declarant |
| 欧盟(最重要)EU (most important) | EU Regulation 2023/1542 | 强制Mandatory | 持续合规ongoing | 2025-08-18 起适用;2027-02-18 起标签信息强制、便携式电池须可安全取出更换;2026-08-18 起碳足迹申报范围扩大;超过 2kWh 工业电池须配电池护照;须指定欧盟授权代表Applies from 18 Aug 2025; from 18 Feb 2027 labelling is mandatory and portable batteries must be safely removable and replaceable; carbon-footprint scope widens from 18 Aug 2026; industrial batteries above 2 kWh need a Battery Passport; an EU authorised representative is required |
| 欧盟其他EU other | CE + RoHS + REACH + 包装法Packaging + WEEE | 强制Mandatory | 2–6 周weeks | 德国、法国另有单独包装法与 WEEE 注册(LUCID / ADEME),必须逐国完成Germany and France run separate packaging and WEEE registrations (LUCID / ADEME) — do them country by country |
| 安全(便携 / 轻型车)Safety (portable / light vehicle) | IEC 62133-2 / EN 62133-2 / UL 2054 / UL 4200A | 视市场强制market-dependent | 4–8 周weeks / 3–8万元 RMB | 带 USB / AC 输出的便携电源通常还需 IEC 62368-1(美 UL 62368-1)Portable stations with USB or AC output normally also need IEC 62368-1 (UL 62368-1 in the US) |
| 安全(轻型车辆)Safety (light vehicle) | UL 2271 / UL 2580 | 北美渠道普遍要求widely required in NA | 10–20 周weeks / 20–60万元 RMB | 亚马逊等平台会直接要求 UL 2271 + UN38.3 报告才能上架Marketplaces such as Amazon require UL 2271 plus UN38.3 before listing |
| 安全(储能)Safety (storage) | IEC 62619 + IEC 63056 + UL 1973 + UL 9540/9540A | 强制或准强制mandatory or de facto | 8–16 周weeks / 15–50万元 RMB | 欧盟储能项目普遍要求 IEC 62619 + CE;美国大型储能还须 UL 1973 + UL 9540/9540A 热失控蔓延火试验,费用高、排队久EU projects generally require IEC 62619 with CE; US grid storage also needs UL 1973 and the UL 9540/9540A propagation fire test — expensive, long queues |
| 户储 / 并网Residential and grid | UL 2743 / UL 1741 + IEEE 1547 / VDE-AR-N 4105 / CEI 0-21 | 强制或并网要求mandatory or grid code | 12–24 周weeks | AC 输出一体机要同时过电池安全与并网标准两套体系,报价时必须合并考虑AC-integrated units must clear both battery-safety and grid-code regimes — price them together |
| 工业车辆Industrial vehicles | EN 1175 + EN 61373 | 欧盟整车指令要求EU machinery directives | 6–12 周weeks | EN 1175 关注爬电距离与电气间隙,BMS 板与铜排布局要提前按此设计,改板代价极高EN 1175 governs clearance and creepage — lay out the BMS board and busbars for it up front; rework is very costly |
| 轨道交通Rail | EN 50155 + EN 45545-2 + EN 61373 | 欧盟强制mandatory in EU | 6–12 个月months | 温度级、振动级、供电中断级须在合同里写明具体等级代号,不能只写标准号State the exact temperature, shock and supply-interruption class codes in the contract — the standard number alone is not enough |
| 中国国内口径China domestic | GB 38031 / GB/T 43568-2026 / GB 43854 / GB/T 36276 | 车用与两轮车为强制mandatory for EV and e-bike | — | 对外宣传与运输申报一律按 GB/T 43568-2026 口径:电解液质量占比 >20% 为液态,5%–20% 为「混合固液电池」(俗称半固态),低于 5% 且通过 120℃ 真空 6h、失重率 ≤0.5% 才可称「全固态」Marketing and shipping declarations must follow GB/T 43568-2026: above 20% liquid electrolyte by mass is a conventional liquid cell, 5–20% is a hybrid solid-liquid cell (colloquially semi-solid), and only below 5% — passing 120 ℃ vacuum for 6 h at ≤0.5% weight loss — may be called all-solid-state |
| 美国(市场准入侧)US (market access) | 301 关税Section 301 tariffs / IRA FEOC / UFLPA | 视客户与项目customer-dependent | — | IRA 合规敏感项目会追溯电芯与正负极材料的原产地与股权构成,须能提供供应链溯源文件;关税随政策变动,报价须注明有效期IRA-sensitive programmes trace cell and electrode-material origin and ownership — traceability files are required; tariffs move with policy, so date every quotation |
| 其他主要市场Other markets | 韩国Korea KC / 日本Japan PSE + JIS C 8715 / 印度India BIS / RCM / UKCA / SASO+SABER | 各市场强制mandatory per market | 4–12 周weeks | 同一款产品可复用 IEC 62133-2 报告转 KC 与 PSE,能省一轮测试An IEC 62133-2 report can be reused for KC and PSE, saving a full test round |
| 软包形态专项Pouch-specific | 无独立强制标准,但有额外测试要求no standalone standard, extra tests apply | 客户规格常见要求common in customer specs | +1–2 周weeks | 软包无金属外壳,客户与认证机构常额外要求挤压、针刺、低气压(高空)与热扩散试验;水下充油方案还须提供耐压与渗漏报告Without a metal can, customers and labs often add crush, nail, low-pressure and propagation tests; oil-filled subsea designs also need pressure and leaktightness reports |
CLARIFY BEFORE QUOTING
客户常把「软包电芯做的电池包」简称为软包电池。必须确认是电芯形态要求还是成品外形要求 —— 两者工艺与成本结构不同,软包 PACK 需要侧板压紧结构与膨胀预留。Customers often mean a pouch-cell PACK. Confirm whether it is a cell-format or an enclosure requirement — the process and cost structures differ, as pouch PACKs need side-plate clamping and swell allowance.
2026 年市面可采购的绝大多数是混合固液(半固态),仍含 5%–20% 电解液。请向电芯方索取电解液含量与真空失重检测报告,并按 GB/T 43568-2026 口径表述。Almost everything purchasable in 2026 is hybrid solid-liquid, still containing 5–20% electrolyte by mass. Ask the cell supplier for electrolyte-content and vacuum weight-loss reports, and use GB/T 43568-2026 wording.
确认是电芯级还是整包级、质量还是体积能量密度。整包级做到 250Wh/kg 在当前量产条件下已属领先水平。Confirm cell- versus pack-level and gravimetric versus volumetric. A 250 Wh/kg pack is already leading-edge under today's volume-production conditions.
确认测试条件:倍率(0.5C 还是 1C)、放电深度、温度、截止容量。同一只电芯在 0.5C/25℃/80% DOD 与 1C/45℃/100% DOD 下寿命可差 3 倍以上。Confirm rate, depth of discharge, temperature and cut-off. The same cell can differ more than 3× between 0.5C/25 ℃/80% DoD and 1C/45 ℃/100% DoD.
NEXT STEP